Home Products Acrylic Coating Acrylic Paint High-Performance Acrylic Thick-Film High-Solids Protective Finish for Industrial Steel And Structural Applications
Single-Component Acrylic Topcoat · Fast Drying · Low-Temperature Applicable

Acrylic Thick Film Finish
Fast-Drying Weather-Resistant Topcoat for Steel & Containers

Acrylic Thick Film Finish is a single-component physical drying coating based on acrylic resin, with great weather resistance as well as light and color retention. Beyond being a good choice for decoration, the film resists ocean water, aliphatic solvents and splashes of animal and plant oils. More importantly, it dries quickly and can be applied in low-temperature environments. Supplied ready to use at a standard 60 μm dry film (about 109 μm wet), it is the recommended topcoat for containers, steel structures and workshops — and is commonly seen on equipment and bridges.

Single-component · ready to useLow-temperature applicable · fast drying6.99 m²/kg at 60 μm DFTWeather, light & color retention20 L / 22 kg · 12-month shelf life
YMS acrylic thick film finish — painted steel workshop structure with YMS Paint bucket
26-year source factory · local plant in Indonesia Single-component physical drying acrylic resin — no hardener, ready to use Fast drying and applicable in low-temperature environments 60 μm DFT in one thick coat — 6.99 m²/kg theoretical coverage Exported to 87 countries

Technical Parameters

Acrylic Thick Film Finish — key figures

ColorCustomized
Gloss / finishHigh gloss, flat, matte
CompositionSingle-component physical drying coating based on acrylic resin
Density~1.31 kg/L (after mixing)
Solid volume(55 ± 2)%
Standard film thickness60 μm dry film thickness (about 109 μm wet film thickness)
Theoretical spreading rate6.99 m²/kg at 60 μm dry film thickness
MixingReady to use — single component, no hardener and no mixing ratio required
ThinnerAcrylic thinner — 0–15% by weight of paint for airless spray
Application toolsAirless spray: nozzle tip 0.017–0.023 inch, spray pressure 15–18 MPa; brush and roller recommended — the required film thickness must be achieved in all cases
Drying schedule (10 / 20 / 30°C)To touch (30 μm): 2 h / 1 h / 30 min; to handle (30 μm): 8 h / 4 h / 3 h
Min. recoating time8 h / 4 h / 3 h at 10 / 20 / 30°C — make sure there is no chalking or other contamination before recoating; actual drying and recoating times depend on temperature, dry film thickness, ventilation, humidity and mechanical strength
Flash point25°C — flammable, keep away from flame and fire, no smoking in the working area
Application conditionsSubstrate temperature at least 3°C above dew point, relative humidity below 85%; measure temperature and humidity close to the substrate
Surface treatmentAll surfaces to be coated shall be clean and dry, evaluated and treated according to ISO 8504; over painted coatings, apply only to a clean, dry and well-compatible primer
Classic coating systemEpoxy Zinc Rich Primer 2 × 50 μm + Epoxy Mica Iron Oxide Intermediate Paint 2 × 50 μm + Acrylic Thick Film Finish 2 × 30 μm (dry film thickness)
Shelf life & storage12 months at room temperature in a shady, dry and ventilated warehouse; test the product before use if the shelf life is exceeded
Packing20 L container, 22 kg net weight
Typical usesHighly recommended as a topcoat for containers, steel structures and workshops; also commonly seen on equipment and bridges

* Data from the YMS Acrylic Thick Film Finish technical datasheet. Full TDS, MSDS and test reports are available on request. Certificates: CE, ISO 9001, ISO 14001, OHSAS 18001, ROHS, SASO and SGS.

Need a fast-drying topcoat specification? Send us the structure type, site temperature, environment and color/gloss target — free one-to-one system recommendation from our technical team.
WhatsApp Enquiry

Product Packaging & Supply

Factory-direct supply, packed and shipped from the JIANBANG plant

JIANBANG factory, packed paint kits and container loading for export
  • 20 L / 22 kg Standard PackSingle-component finish supplied ready to use — one 20 L container at 22 kg net, palletized and container-loaded at our Changzhou plant. No hardener to pair, no pot life to manage on site.
  • 12-Month Shelf LifeStored in a shady, dry and ventilated warehouse at room temperature, the product keeps for 12 months. Batches beyond shelf life are tested before use, so maintenance stock stays reliable across seasons.
  • Custom Colors & GlossColor is fully customized and the finish is available in high gloss, flat or matte — drum branding and private-label packing arranged per destination market.
  • Full Project SupportWe advise on surface preparation to ISO 8504, thinner ratios, recoat timing and system matching — from epoxy zinc-rich primers to epoxy mica iron oxide intermediates.
  • Safe HandlingFlash point 25°C — keep away from flame and fire, no smoking in the working area, and keep the site ventilated. Refer to the MSDS before use; dispose of used paint barrels correctly.
Request a Sample & Quote

Core Functions

Why Acrylic Thick Film Finish keeps projects moving in cool weather

Fast Drying

Quick Turnaround, Even in Low Temperatures

This product dries quickly and can be used in a low-temperature environment — at 10°C it is touch-dry in 2 h and handleable in 8 h, so outdoor steel and container work keeps its schedule when colder conditions would stall ordinary coatings.

Weather

Weather, Light & Color Retention

Based on acrylic resin, the film has great weather resistance and keeps both light and color over time — a good choice for decoration on structures that stay in public view through sun, rain and coastal exposure.

Resistance

Ocean Water, Solvents & Oil Splashes

The film resists ocean water, aliphatic solvents and splashes of animal and plant oils — a practical barrier for container yards, port equipment and plant areas where washdown and oil splash are routine.

Thick Film

60 μm DFT in One Thick Coat

With (55 ± 2)% solid volume, a standard 60 μm dry film (about 109 μm wet) covers 6.99 m²/kg — the required thickness is reached efficiently by airless spray, brush or roller.

Simple

Single Component, Ready to Use

No hardener, no mixing ratio and no pot life — just stir, thin with acrylic thinner (0–15% for airless spray) and apply. Fewer on-site steps mean fewer mixing errors and less waste on maintenance jobs.

Finish

Three Gloss Levels, Any Color

Color is customized and the finish is offered in high gloss, flat or matte — match the corporate color on a container fleet or the subdued look of a workshop frame without changing the protective system.

Applications

Where Acrylic Thick Film Finish goes to work

Freshly painted blue and red shipping containers stacked at a container terminal
Shipping Containers

Container fleets need a colorful, weather-resistant topcoat that dries fast between handling cycles — the single-component finish keeps its light and color through ocean air and strong sunlight.

Container reach stacker and loading platforms coated in light-gray and blue gloss paint
Logistics Equipment

Reach stackers and loading platforms see constant abrasion, washdown and oil splash — the film resists aliphatic solvents and animal and plant oil splashes while holding its corporate color.

Painted steel roof trusses and columns inside a modern workshop with skylights
Steel Structure Workshops

Workshop steel is often coated indoors or in cool seasons — fast drying and low-temperature applicability keep the job moving, with a clean decorative finish in high gloss, flat or matte.

Exterior steel portal frames of a new warehouse finished in light-gray satin paint
Steel Buildings & Frames

New-build steel frames need a topcoat that reaches 60 μm dry film efficiently — (55 ± 2)% solid volume gives 6.99 m²/kg coverage over the classic zinc-rich plus micaceous iron oxide system.

Steel truss bridge freshly painted in light-gray weather-resistant finish over a river
Bridges

Bridge steel stays exposed to weather and ocean water in coastal crossings — great weather resistance plus light and color retention protect the structure and keep its appearance for years.

Large industrial machinery housings coated in light-gray and blue satin-gloss paint
Industrial Equipment

Equipment housings and plant machinery are commonly finished with this topcoat — resistance to ocean water, aliphatic solvents and oil splashes suits demanding service, with a customized color to match the site.

How to Use · 4-Step Operating Procedure

From surface preparation to the finished fast-drying film

1
Prepare the SubstrateAll surfaces must be clean and dry, evaluated and treated according to ISO 8504. Over existing coatings, apply only to a clean, dry, well-compatible primer. Work only when the substrate is at least 3°C above dew point and relative humidity is below 85%, measuring close to the substrate.
2
Stir & Thin — Ready to UseSingle component: no hardener and no mixing ratio. Simply stir the paint and, if needed, thin with acrylic thinner at 0–15% by weight for airless spray. There is no pot life to watch on site.
3
Spray, Brush or Roll — 60 μm DFTAirless spray: nozzle tip 0.017–0.023 inch at 15–18 MPa; brush and roller are recommended as well — whatever the tool, the required film thickness must be achieved. Standard film: 60 μm dry (~109 μm wet), 6.99 m²/kg.
4
Dry & RecoatAt 20°C: touch-dry in 1 h, handleable in 4 h, minimum recoat interval 4 h (at 10°C: 2 h / 8 h / 8 h; at 30°C: 30 min / 3 h / 3 h). Ensure no chalking or contamination before recoating. Flash point 25°C — no flames on site, keep the area ventilated.

Note: application parameters follow the YMS Acrylic Thick Film Finish datasheet — we match a dedicated system one-to-one based on your substrate, environment and service-life target. Classic system: epoxy zinc-rich primer 2 × 50 μm, epoxy mica iron oxide intermediate 2 × 50 μm, this finish 2 × 30 μm. Refer to the MSDS before use and dispose of packaging responsibly.

See It In Action

Application and quality-control moments on real projects

Worker abrasive blasting a steel tank shell to clean metal before topcoating

Surface preparation comes first — all surfaces to be coated must be clean and dry and treated according to ISO 8504, whether bare steel or a compatible primer.

Painter airless spraying light-gray acrylic thick film finish onto a primed steel beam

Ready to use, the finish goes on by airless spray, brush or roller at 60 μm dry film — a smooth even coat that dries quickly, even in low-temperature conditions.

Inspector checking dry film thickness on a freshly finished light-gray painted steel panel

Film thickness and finish are verified before hand-over — the required 60 μm dry film in high gloss, flat or matte, checked on the completed surface.

Why Choose YMS Paint / JIANBANG Coatings

More than a paint supplier — your coatings partner

26 YearsSource factory specialized in anticorrosion, floor and specialty coatings.
87 CountriesExported worldwide with a local plant and service in Indonesia.
Fast-Cure ChemistrySingle-component acrylic resin finish proven in cool-weather steel and container work.
Full DocumentsTDS, MSDS, CE, ISO 9001 / 14001, OHSAS 18001, ROHS, SASO and SGS reports supplied.
Free MatchingFree sample testing against your structure, environment and color target before bulk orders.
Custom Packing20 L / 22 kg standard, with drum branding and private-label packing per market.

One Coating Platform, Four Metal Protection Systems

Match the metal protection coating to the substrate, corrosion load and environment

Fast-Drying Topcoat

Acrylic Thick Film Finish

This product — single-component physical drying acrylic finish, 60 μm DFT in one coat, ready to use and applicable at low temperature for containers, steel structures and workshops.

Premium PU Topcoat

Acrylic Polyurethane Finish

Two-component high-gloss weather-resistant finish based on aliphatic isocyanates and hydroxyl resins — salt spray ≥3000 h and aging ≥5000 h for severe marine and chemical service.

Zinc-Rich Primer

Epoxy Zinc Rich Primer

The first layer of the classic system at 2 × 50 μm dry film — anti-corrosion foundation under epoxy intermediates and weather-resistant finishes.

Epoxy Intermediate

Epoxy Mica Iron Oxide Intermediate Paint

The build coat of the classic system at 2 × 50 μm dry film — shields the primer and gives the finish a sound, compatible base.

Frequently Asked Questions

What is Acrylic Thick Film Finish?

A single-component physical drying coating based on acrylic resin. It has great weather resistance as well as light and color retention, is a good choice for decoration, and resists ocean water, aliphatic solvents and splashes of animal and plant oils. It dries quickly and can be used in low-temperature environments.

Where should it be used?

It is highly recommended as a topcoat for containers, steel structures and workshops, and is also commonly seen on equipment and bridges. In the classic coating system it is applied at 2 × 30 μm dry film over epoxy zinc-rich primer and an epoxy mica iron oxide intermediate.

Why is it suitable for low-temperature work?

Because it is a fast-drying physical-drying acrylic coating that can be applied in low-temperature environments. Even at a 10°C substrate temperature it is touch-dry in 2 h and handleable in 8 h, with a minimum recoat interval of 8 h — so cool-season projects keep their schedule.

How well does it retain appearance outdoors?

The acrylic resin film has great weather resistance and keeps both light and color over time. It also resists ocean water, aliphatic solvents and splashes of animal and plant oils, which is why it is used on containers and port equipment as well as on buildings.

Is it single-component, and how is it applied?

Yes — it is ready to use with no hardener, no mixing ratio and no pot life. Thin only with acrylic thinner (0–15% by weight of paint for airless spray). Airless spray: nozzle tip 0.017–0.023 inch at 15–18 MPa; brush and roller are recommended too. The required film thickness must be achieved whatever the tool.

How fast does it dry and when can I recoat?

At 10 / 20 / 30°C: to touch (30 μm) 2 h / 1 h / 30 min; to handle (30 μm) 8 h / 4 h / 3 h; minimum recoating time 8 h / 4 h / 3 h. Make sure there is no chalking or other contamination before recoating. Actual times depend on temperature, film thickness, ventilation, humidity and mechanical strength.

What surface and application conditions are required?

All surfaces must be clean and dry and treated according to ISO 8504; over painted coatings, apply only to a clean, dry, well-compatible primer. Substrate temperature must be at least 3°C above the dew point and relative humidity below 85%, measured close to the substrate.

How is it packed, stored and what is the shelf life?

Standard packing is a 20 L container at 22 kg net weight. Store in a shady, dry and ventilated warehouse at room temperature; shelf life is 12 months, and product beyond shelf life should be tested before use. Flash point is 25°C — keep away from flame and fire, no smoking in the working area.

Get a Sample & a Fast-Drying Topcoat Specification

Tell us the structure type, site temperature, environment, area and color/gloss target — our engineers reply within 24 hours with a matched system, coverage plan and quotation.

Or reach us directly: WhatsApp +86-17312895118 · inquiry@jsbj88.com · reply within 24 hours.

WhatsApp Us · +86-17312895118 Email: inquiry@jsbj88.com
Apply Our Best Quotation
Apply Our Best Quotation

Minimum Order Quantity (MOQ): 200 KG or 200 m² per product

© COPYRIGHT 2024 CHANGZHOU YMS NEW MATERIALS TECHNOLOGY CO., LTD. ALL RIGHTS RESERVED.